Skip to content

Progressor 200 vs 500: which one do you need?

The Progressor 200 and Progressor 500 are the same Bluetooth dynamometer in two load ranges. Both stream live force data at 80 Hz to the free Tindeq app on iOS and Android, both charge over USB-C, and both work with the open Bluetooth API. The difference is how much force you need to measure.

The short answer

  • Choose the Progressor 200 if you are a climber testing and training finger strength, one-arm pulls or grip, or if you mostly measure single limbs. Its range is 200 kg (2000 N).
  • Choose the Progressor 500 if you are a physio, S&C coach or researcher who needs high-load tests such as an isometric mid-thigh pull, or leg and hip tests where forces go past 200 kg. Its range is 500 kg (5000 N).

Specifications side by side

Progressor 200Progressor 500
Design load (full scale)2000 N (200 kg)5000 N (500 kg)
Safe overload120% of full scale120% of full scale
Limit overload150% of full scale140% of full scale
Sampling frequency80 Hz80 Hz
Precision0.25% of full scale0.25% of full scale
Non-linearity0.1% of full scale0.05% of full scale
Repeatability0.1% of full scale0.1% of full scale
Hysteresis0.1% of full scale0.1% of full scale
BatteryRechargeable, USB-CRechargeable, USB-C
EnclosureABSABS
ReplacesProgressor 150Progressor 300

Precision is given as a percentage of full scale, so it is an absolute figure: 0.25% of 200 kg is 0.5 kg on the Progressor 200, and 0.25% of 500 kg is 1.25 kg on the Progressor 500. If all your measurements stay well below 200 kg, the Progressor 200 gives you the finer resolution.

For climbers

Most climbers pick the Progressor 200. Hang it from a sling or anchor, clip an edge or a pair of rings below it, and the app shows your pulling force live. You can run repeaters, critical force and endurance tests, and track the numbers over time. For finger and pulling tests the 200 kg range is usually enough, and the smaller range gives finer absolute precision.

For physios, coaches and researchers

Pick the Progressor 500 when the test involves the whole body or the legs. An isometric mid-thigh pull, deadlift-position pulls and many hip and knee tests can produce forces above 200 kg in trained athletes. The Progressor 500 measures in line with a strap, bar or chain, so you rig it between an anchor and the athlete and read the force curve on a phone or tablet. For upper-limb and grip tests the Progressor 200 is often enough, and some clinics keep one of each.

The Progressor has been the subject of published validity and reliability studies; you’ll find the papers on our research page.

What is the same on both

  • The free Tindeq Progressor app for iOS and Android, with live force curves and saved results.
  • The open Bluetooth API, so you can stream raw data into Python or your own software.
  • Rigging: attach with nylon or Dyneema webbing; carabiners work but wear the load-cell body faster, and chains can add torsion and vibration. See the user manual.
  • Export to a spreadsheet: see Import data to spreadsheet.

I have an older Progressor 150 or 300

The Progressor 200 replaces the 150, and the Progressor 500 replaces the 300. The new models have a USB-C rechargeable battery and an ABS enclosure. If your older unit has battery or connection problems, start with Progressor 150 & 300 troubleshooting.

Frequently asked questions

Can I use the Progressor 200 for deadlifts or mid-thigh pulls?

Only if the force stays inside its range. The design load is 200 kg, and the safe overload is 120% of full scale. If you expect pulls above 200 kg, choose the Progressor 500.

Which one should a physiotherapy clinic buy?

If you test lower limbs or whole-body pulls, the Progressor 500. If you mostly test upper limbs, grip and fingers, the Progressor 200 has finer absolute precision. Both use the same app.

Do they use the same app?

Yes. Both connect to the same free Tindeq Progressor app, and you connect from inside the app rather than pairing in your phone’s Bluetooth settings.